How To Load A Grease Gun

If there is air trapped inside unscrew to allow air out. To load a grease gun from large containers instead of cartridges unscrew the grease gun head from the barrel.

Pin On Top Grease Gun

Loading and re-loading it can be a grubby task.

How to load a grease gun. When you buy a mini grease gun the parts are not usually pre-assembled. Press down firmly on the nozzle until you feel it click into position. Screw the barrel into the head of the gun.

Screw gradually and unfasten the bar. The handle and the applicator tube are connected to. Then depress the rod handle to force grease into the head of the gun which will push the air out.

Prevent air locks by filling the grease gun head before adding the new cartridge Photo 1. The model is the. Scoop any remaining grease out of the old cartridge and pack it into the head.

So Pull the pull rod all the way out using the t-grip handle and get ready to load the grease. However using a grease gun can sometimes be a technical and complex task. Hold the open end into the container with the barrel down.

The dome of grease is ready to pack the grease gun head. My grease gun holds 3 oz grease cartirdges. Open the end of the cartridge and peel of the mask from it.

Remove both ends of the grease cartridge. When I lube up my RV morothomes mechanical parts I have to change the grease cartridge at least once. Then back it off two turns and release the spring tension.

Generally all grease guns use cartridges but they can vary in size so youll need to make sure that your grease gun is suitable for the cartridge size that youre using. With the t-handle out place the cartridge into the barrel. You can load your grease gun without a cartridge by following the steps below.

Insert the new cartridge and screw on the barrel until it seats against the head. Of course for your grease gun to work youll need to ensure that its loaded properly. There are essentially two types of grease guns with a cartridge and without a.

This will further push. This allows you to pull grease into your barrel. Then draw back the plunger rod so the reservoir fills.

Now there is going to be a grease full cartridge that will go inside the barrel. To check the amount of grease remaining just pull down on the follower rod. Make sure the rim of the cartridge is in contact with the rim of the gun before returning the rod handle to its original position.

How to load a grease gun Remove old cartridge and reset spring First unscrew the end cap from the grease gun and remove the empty cartridge. Amazing tips for loading a grease gun. Place the grease nozzle over the nipple.

Install the end cap and retract the spring by pulling the plunger-rod handle and twisting and locking it in place. How to Load a Grease Gun Cartridge Video. If you have a problem in knowing how to load a grease gun cartridge gently pull the handle and latch it properly.

Fill the barrel of your grease gun by placing the open end into your container full of grease. To use a grease gun start by pulling back the rod handle and placing a grease cartridge into the gun. It will stop when it hits the follower plate at the bottom of the grease and show you how much you have left.

Then stick the open end of the barrel into the container of grease and slowly pull back on the plunger rod to fill the reservoir with grease. Loading your Grease Gun. Some grease guns will require you to fill the barrel.

But you need a big container with a complete load of bulk grease for this. Then unscrew the grease gun head and put the cartridge right into the guns barrel. Having said that please note the task becomes easier if proper instructions are followed and you know how to load a grease gun properly.

I had an older model grease gun that needed refilling since I couldnt find a how to online I made my own for others in the same situation. The first thing youre going to do is separate your grease gun head from the barrel so unscrew your gun head from the cap. The trick is to pump until you are almost out of grease but there is still some in the hose and head of the gun.

Begin pumping the grease and pump until you see excess grease oozing from the nipple. Using a rag push the grease from the bottom of the cartridge to form a large dome of grease on the top. How to Load and Prime a Grease Gun - Part 2.

Pin On Top Grease Gun